| After-sales Service: | on-Line Service |
|---|---|
| Warranty: | One Year |
| Type: | Thermal Evaporation Coater |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
New Design 5 inch proximity thermal evaporation coater coating furnace
OVERVIEW--THERMAL EVAPORATION
Thermal evaporation is a popular physical vapor deposition technique because of its simplicity. During this process, a material in a high-vacuum environment is heated to its evaporation point by joule heating of the resistive boat in which it is located. The vaporized molecules then travel from the source to the substrate where they nucleate together, forming a thin film coating. A wide variety of materials can be deposited using this technique such as aluminum, silver, nickel, chrome, magnesium, among many others.
Specifications of Proximity Thermal Evaporation Coater
| Items | Detail |
| Supply voltage | AC220V,50/60Hz |
| Maximum power | 10KW |
| Structure | Two temperature controllers are used to control the top and bottom two sets of heating elements respectively. A float flow meter is installed, and gas can be introduced into the vacuum chamber. |
| Basic parameters | Working temperature: up to 800C Recommended heating rate: ≤10C/s (each temperature zone is heated separately) |
| Temperature control accuracy | Two sets of infrared lamps are used as heating elements, which are located at the top and bottom respectively. In order to reduce heat radiation and achieve a faster cooling rate, the heating elements are installed in a stainless steel shell with a water-cooled interlayer (the stainless steel shell is made of 316 stainless steel. It adopts thermal conductivity. A high rate aluminum nitride ceramic sheet (5" X5^ Xo. 5nn] thickness) is used as the sample stage to achieve better heating uniformity. The bottom sample stage. A 5° X5* graphite crucible can be placed on it to hold the evaporated raw materials. |
| Temperature Control System | Two precise temperature control systems independently control the upper and lower heating zones, and can set 30-stage heating and cooling programs. Each temperature control system is equipped with over-temperature and couple-break protection. PC communication interface, software can be installed, and the temperature control program can be installed. and temperature curve imported into the computer. |
| Temperature measuring element | Two K-type thermocouples. , mounted on the top and bottom, are in contact with aluminum nitride ceramic sheets. |
| Precautions for use | 1. The air pressure in the furnace tube should not be higher than 0.02MPa 2. Due to the high air pressure inside the gas cylinder, a pressure reducing valve must be installed on the gas cylinder when gas is introduced into the furnace tube. It is recommended to purchase a pressure reducing valve in our company. More precise and safe to use 3. The air pressure in the furnace tube should not be higher than 0.02MPa 4. Due to the high air pressure inside the gas cylinder, a pressure reducing valve must be installed on the gas cylinder when gas is introduced into the furnace tube. It is recommended to purchase a pressure reducing valve in our company. will be more precision and safety 5. When the temperature of the furnace body is higher than 1000C, the furnace tube cannot be in a vacuum state, and the air pressure in the furnace tube must be equal to the atmospheric pressure and kept at normal pressure. 6. The gas flow into the furnace tube should be less than 200SCCM to avoid the impact of the cold atmospheric flow on the heating quartz tube 7. Long-term use temperature of quartz tube < 1100C 8. For the sample heating experiment, it is not recommended to close the exhaust valve and the intake valve at the flange end of the furnace tube. 9. If you need to close the air valve to heat the sample, you should always pay attention to the indication of the pressure gauge. 10. If the air pressure indication is greater than 0.02MPa, the vent valve must be opened immediately to prevent accidents (such as furnace tube rupture, flange flying out, etc.) 11.The gas flow into the furnace tube should be less than 200SCCM to avoid the impact of the cold atmospheric flow on the heated quartz tube. 12. The long-term use temperature of the quartz tube is < 1100C, 0.02MPa, the vent valve must be opened immediately to prevent accidents (such as furnace tube rupture, flange flying out, etc.) |
| Opening method | Electric lift cover |
| Flowmeter | Two-way float flowmeter |
1. We have thermal evaporation coater with 1/2/3/4/8... evaporation sources, can evaporation metal and organic material
2. Chamber material: High purity quartz--- low vacuum, SS304 chamber-- high vacuum
3. Film thickness monitor is optional
4. Thermal evaporation, E-beam, magnetron sputtering in one machine is available
5. Different material of evaporation source is available
6. Customize thermal evaporation coater according to your process is available
Zhengzhou Tainuo Film Materials Co., Ltd. is a comprehensive company integrating design, research and development, production and sales.
Our company's main products are: spin coater, thermal evaporation coater, magnetron sputter coater, plasma sputter coater, E-beam evaporation coater, PLD pulse laser coating machine, plasma cleaner, CVD system, PECVD system, diamond wire cutting machine, melting furnace/stove, arc melting furnace, etc.
Our products are widely used in the field of materials science research. We have extensive cooperation with domestic universities, laboratories, and new material companies. It has been successfully exported to more than 20 countries and regions including the United States, the United Kingdom, Germany, Russia, Switzerland, Canada, Brazil, etc. and have established long-term cooperative relationships with local dealers.
If you are conducting materials research, please contact us and we will provide you with customized services to make your research experiments smoother!
We can ship the thermal evaporation coater by sea, by air, by land, b Express, also can arrange shipment according to your requirement.
Q. Are you manufacturer or trading company?
A. We are professional manufacturer of laboratory instruments, We have professional R&D team and workshop, which can promise the qulaity and after-sale service.
Q. How's your warranty?
A. Our warranty is 12 months, and provide lifetime maintenance. We provide 24 hours on-line service.
Q. How long is your delivery time? If I want to customize the instrument, how long does it take?
A. 5-10 days----in store. Customzied products---It usually takes 30-60 days depending on your requirements.
Q. Power supply and plug?
A. We can provide products accroding to your local voltage and plug standard.
Q. How to pay?
A. T T, L / C, D / P, etc.
Q. How is the package of goods? Delivery methods?
A. Standard export fumigation sign wooden box packaging or as your requirements.
WE WANT TO HEAR ABOUT YOUR PROCESS!
Please get in touch and we can collaborate on your project. When we work together, amazing things can happen. Your brilliant ideas with our innovative team will create the tool that will bring your research or production to the next level. We're looking forward to hearing from you.
){kind=link}